精品熟女60老妇av免,欧美午夜,中文字幕无码一区二区三区亚洲,女人av天堂

Analysis on the Operating Rules of Pipe Winch

Release time:

2021-10-29

The purpose of the pipe winch machine: the pipe winch machine is used for wire and cable conductors and insulated wire strands.

Analysis on the Operating Rules of Pipe Winch

operating procedures of pipe winch:

1. The purpose of the pipe twisting machine: the pipe twisting machine is used for wire and cable conductors and insulated wire strands.

2. Service scope of pipe winch

Covering range 6GJ12GJ

Single wire diameter mm 0.2~0.85 0.2~0.85

Kink diameter mm 0.6~2.5 1.5~4

Tube speed rotation/min 10~120010~750

Traction wheel diameter mm318

Pitch range mm 6.08~68.706.08~68.70

Departure speed m/min 16.2~68.716~69

Wire plate size mm 125~200

Wire tray size mm 400~630

3. Pipe winch production

3.1 production preparation

3.1.1 Wear labor protection articles and prepare production articles.

3.1.2 Receive data in accordance with the production task notification and process documents. Confirm whether the information received is qualified.

3.1.3 Check the transmission conditions of the machine, and add lubricating oil to the transmission gears, joysticks and pipes, steel wire frame bearings and cable screws of the winch.

3.1.4 Press the start switch, run empty, confirm the direction of the tube according to the process, and turn on the official power after the equipment is running normally.

Install the pitch wheel according to the process requirements in 3.1.5. Select the separate body mold and place it in the mold base.

3.1.6 Open the protective cover, first pull the spring latch on the swing side, take out the steel wire shaft from the swing bar respectively, insert it into the whole steel wire disc hole respectively, put it into the swing bar, and lock the bolt.

3.1.7 The blue is equipped with a braking end, contacting the edge of the side plate of the wire plate, and the blue frame is equipped with a tension adjustment nut, and the tension of the wire plate is adjusted according to the diameter of the wire.

3.1.8 The single-line installation of the full-wire disc head on a shelf passes through the empty shaft on the front of the tube, the guide wheel of the tube wall and the steel wire mold of the circular support plate, and then attracts forward along the tube wall, and then leads out from the guide wheel. Control ring through the cutter. After attracting too much wire plate, guide the excessive volume mold hole fixed in place. The mold is fixed on the mold frame and pressed with a platen.

3.1.9 The pipe winch machine uses the towing wire to wind the towing coil around the hollow shaft of the package for more than 3 turns, and then receives the towing wire to the receiving reel through the wire arrangement machine. A ship plate wire that connects the other end of the traction line and is put together.

3.1.10 Gloves shall be worn when stranding silver wire, and hands shall not be touched directly during stranding.

3.2 kink

3.2.1 Turn on the power supply of the pipe winch.

3.2.2 Press the start switch of the pipe winch, slowly adjust the speed regulating device, adjust the clamp, start the stranded wire (cable core) on the traction line, and stop the machine when it reaches 0.5-1 turn, so as to ensure that the direction, pitch and outer diameter of the stranded wire meet the process requirements. Adjust immediately when not in time, turn on the rear power supply, the stranded wire reaches the tail plate, stop the machine, and eliminate the traction line. Pull the kink (cable core) out of the core of the cable tray and fix it on the edge of the disk.

3.2.3 Adjust the mold to an appropriate position to prevent the phenomenon of jumper or single wire pulling, so as to flatten and round the kink.